简体 | 繁體 | FastenerExpo |

Plain Bearings - Ring Type Thrust Washers made from Strip

ISO 6525 - 2018

Display drawing:

国际ISO 6525 - 2018 ISO6525 6525ISO Plain Bearings - Ring Type Thrust Washers made from Strip
Size
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
d min=nominal size
max
D max=nominal size
min
h max=nominal size
min
C Nominal Size
max
min
F Nominal Size
max
min
6 7 8 9 10 12 12 14 14 16 16 18 18 20 20 22
6.25 7.25 8.25 9.25 10.25 12.25 12.25 14.25 14.25 16.25 16.25 18.25 18.25 20.25 20.25 22.25
16 17 18 19 22 24 24 26 26 30 30 32 32 36 36 38
15.75 16.75 17.75 18.75 21.75 23.75 23.75 25.75 25.75 29.75 29.75 31.75 31.75 35.75 35.75 37.75
1 1 1 1 1 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
0.95 0.95 0.95 0.95 0.95 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45
11 12 13 14 16 18 18 20 20 23 23 25 25 28 28 30
11.15 12.15 13.15 14.15 16.15 18.15 18.15 20.15 20.15 23.15 23.15 25.15 25.15 28.15 28.15 30.15
10.85 11.85 12.85 13.85 15.85 17.85 17.85 19.85 19.85 22.85 22.85 24.85 24.85 27.85 27.85 29.85
1.5 1.5 1.5 1.5 1.5 1.5 1.5 2 2 2 2 2 2 3 3 3
1.9 1.9 1.9 1.9 1.9 1.9 1.9 2.4 2.4 2.4 2.4 2.4 2.4 3.4 3.4 3.4
1.6 1.6 1.6 1.6 1.6 1.6 1.6 2.1 2.1 2.1 2.1 2.1 2.1 3.1 3.1 3.1
Size
22 (23) 24 25 26 (27) 28 30 32 34 36 38 (39) 40 42 (44)
d min=nominal size
max
D max=nominal size
min
h max=nominal size
min
C Nominal Size
max
min
F Nominal Size
max
min
22 24 24 26 26 28 28 32 32 36 36 40 40 40 45 45
22.25 24.25 24.25 26.25 26.25 28.25 28.25 32.25 32.25 36.25 36.25 40.25 40.25 40.25 45.25 45.25
38 42 42 44 44 48 48 54 54 60 60 64 64 64 70 70
37.75 41.75 41.75 43.75 43.75 47.75 47.75 53.75 53.75 59.75 59.75 63.75 63.75 63.75 69.75 69.75
1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45 1.45
30 33 33 35 35 39 39 43 43 48 48 52 52 52 57.5 57.5
30.15 33.15 33.15 35.15 35.15 39.15 39.15 43.15 43.15 48.15 48.15 52.15 52.15 52.15 57.65 57.65
29.85 32.85 32.85 34.85 34.85 38.85 38.85 42.85 42.85 47.85 47.85 51.85 51.85 51.85 57.35 57.35
3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4
3.4 3.4 3.4 3.4 3.4 4.4 4.4 4.4 4.4 4.4 4.4 4.4 4.4 4.4 4.4 4.4
3.1 3.1 3.1 3.1 3.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1
Size
45 48 50 53 (55) 56 (57) 60 63 (65) 67 (70) 71 75 80
d min=nominal size
max
D max=nominal size
min
h max=nominal size
min
C Nominal Size
max
min
F Nominal Size
max
min
45 50 50 55 55 60 60 60 65 65 70 70 75 75 80
45.25 50.25 50.25 55.25 55.25 60.25 60.25 60.25 65.25 65.25 70.25 70.25 75.25 75.25 80.25
70 76 76 80 80 90 90 90 100 100 105 105 110 110 120
69.75 75.75 75.75 79.75 79.75 89.75 89.75 89.75 99.75 99.75 104.75 104.75 109.75 109.75 119.75
1.5 2 2 2 2 2 2 2 2 2 2 2 2 2 2
1.45 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.95 1.95
57.5 63 63 67.5 67.5 75 75 75 83.5 83.5 88 88 92.5 92.5 100
57.65 63.15 63.15 67.65 67.65 75.15 75.15 75.15 83.65 83.65 88.15 88.15 92.65 92.65 100.15
57.35 62.85 62.85 67.35 67.35 74.85 74.85 74.85 83.35 83.35 87.85 87.85 92.35 92.35 99.85
4 4 4 5 5 5 5 5 5 5 5 5 5 5 5
4.4 4.4 4.4 5.4 5.4 5.4 5.4 5.4 5.4 5.4 5.4 5.4 5.4 5.4 5.4
4.1 4.1 4.1 5.1 5.1 5.1 5.1 5.1 5.1 5.1 5.1 5.1 5.1 5.1 5.1
①,D0=D,the torlerance is G10
②,h1 is determined by the posiible wear of the thrust washer, axial clerance and the condition of loading in order to prevent washer escaping out of the recess if the load is reversed.