简体 | 繁體 | FastenerExpo |

Screwd Studs -B.S.W.Thread [Table 6]

BS 2693-1 - 1956

Display drawing:

英标BS 2693-1 - 1956 BS2693-1 2693-1BS Screwd Studs -B.S.W.Thread  [Table 6]
Screw Thread
d
1/4 5/16 3/8 7/16 1/2 9/16 5/8 3/4 7/8 1 1-1/8 1-1/4 1-1/2
PP
Major diameter max
min
Effective diameter max
min
Minor diameter max
min
L min b1=d
b1=1.5d
D
20 18 16 14 12 12 11 10 9 8 7 7 6
0.2500 0.3125 0.3750 0.4375 0.5000 0.5625 0.6250 0.7500 0.8750 1.0000 1.1250 1.2500 1.5000
0.2452 0.3073 0.3695 0.4316 0.4937 0.5560 0.6183 0.7428 0.8674 0.9920 1.1164 1.2413 1.4906
0.2206 0.2798 0.3381 0.3952 0.4503 0.5129 0.5708 0.6903 0.8085 0.9251 1.0388 1.1640 1.3991
0.2177 0.2767 0.3349 0.3918 0.4466 0.5091 0.5668 0.6860 0.8039 0.9200 1.0335 1.1585 1.3933
0.1886 0.2442 0.2981 0.3495 0.3969 0.4595 0.5126 0.6263 0.7374 0.8451 0.9473 1.0725 1.2924
0.1831 0.2383 0.2919 0.3428 0.3897 0.4521 0.5050 0.6182 0.7288 0.8360 0.9376 1.0627 1.2818
7/8 1-1/8 1-3/8 1-5/8 1-3/4 2 2-1/4 2-5/8 3-1/8 3-1/2 4 4-1/2 5-1/4
1 1-1/4 1-1/2 1-3/4 2 2-1/4 2-1/2 3 3-1/2 4 4-1/2 5 6
1/4 5/16 3/8 7/16 1/2 9/16 5/8 3/4 7/8 1 1-1/8 1-1/4 1-1/2
①,The length of thread on the nut end of the stud shall not include the run-out threads and shall be equal to twice the nominal diameter of the thread, except in the case of short studs where this would result in a length of plain portion less than 1/ 2 D. In such cases a length of plain portion equal to 1/ 2 D should be allowed for before threading the remainder for the nut end.
②,Metal end (b1):
i) The length of the thread on the metal end of the stud shall include the run-out threads and shall be equal to the nominal diameter of the thread or to one and a half times the nominal diameter of the
thread, as specified by the purchaser.
ii) The length of thread run-out shall be not less than 2 pitches or more than 2-1/2 pitches.
iii) The tolerance on the length of the thread shall be plus or minus 1/32 in., or plus or minus half a pitch, whichever is the greater.
③,Ends of studs:
a) Metal end: The metal end of the stud shall be finished with a flat chamfer with a 90° included angle to a depth slightly exceeding the depth of thread.
b) Nut end: The nut end of the stud (except studs with Unified threads) shall be finished with a radius approximately equal to 11/ 4 times the nominal diameter. Unified threads shall have a shallow dog point machined on the nut end.

Similar Standards

1 Studs - Metal end ≈ 1,25 d [DIN]
DIN 939 - 1995
Studs - Metal end ≈ 1,25 d

View Suppliers
2 Studs with Metric Interference Thread MFS - Part 1: Lengths of Engagement ≈ 2 d (Type A) [DIN]
DIN 949-1 - 1995
Studs with Metric Interference Thread MFS - Part 1: Lengths of Engagement ≈ 2 d (Type A)

View Suppliers
3 Studs - Metal End ≈ 1 d [DIN]
DIN 938 - 2012
Studs - Metal End ≈ 1 d

View Suppliers
4 Double End Studs [IFI]
IFI 136 - 2006
Double End Studs

View Suppliers
5 Studs With A Length Of Engagement Equal To About 1d [DIN]
DIN 938 - 1995
Studs With A Length Of Engagement Equal To About 1d

View Suppliers
6 Studs with Metric Interference Thread MFS - Part 2: Lengths of Engagement ≈ 2.5 d (Type B) [DIN]
DIN 949 (-2) - 1995
Studs with Metric Interference Thread MFS - Part 2: Lengths of Engagement ≈ 2.5 d (Type B)

View Suppliers
7 Studs with a length of engagement equal to about 2.5d [DIN]
DIN 940 - 2010
Studs with a length of engagement equal to about 2.5d

View Suppliers
8 Studs with a length of engagement equal to about 2.5d [DIN]
DIN 940 - 1983
Studs with a length of engagement equal to about 2.5d

View Suppliers
9 Studs - Metal end ≈ 2.5d [DIN]
DIN 940 - 1995
Studs - Metal end ≈ 2.5d

View Suppliers
10 Double End Studs-bm=1.25d [GB]
GB 898 - 1988
Double End Studs-bm=1.25d

View Suppliers
11 Double End Studs(Clamping Type) - Product Grade C [GB]
GB 953 - 1988
Double End Studs(Clamping Type) - Product Grade C

View Suppliers
12 Double End Studs For Pipe Flange Connection [GB]
GB /T 9125 - 2003
Double End Studs For Pipe Flange Connection

View Suppliers
13 Double End Studs-bm=1d [GB]
GB 897 - 1988
Double End Studs-bm=1d

View Suppliers
14 Double End Studs For Pipe Flange Connection - PN designated [GB]
GB /T 9125.1 - 2020
Double End Studs For Pipe Flange Connection - PN designated

View Suppliers
15 Double End Studs  b1=1.5d [GB]
GB 899 - 1988
Double End Studs b1=1.5d

View Suppliers
16 Double studs [JIS]
JIS B 1173 - 1995
Double studs

View Suppliers
17 Studs [JIS]
JIS B 1173 - 2010
Studs

View Suppliers
18 Double End Studs-bm=2d [GB]
GB 900 - 1988
Double End Studs-bm=2d

View Suppliers
19 Double End Studs For Pipe Flange Connection [GB]
GB /T 9125 - 2010
Double End Studs For Pipe Flange Connection

View Suppliers
20 Double End Studs (Clamping Type)-Product Grade B [GB]
GB 901 - 1988
Double End Studs (Clamping Type)-Product Grade B

View Suppliers
21 Double End Studs - Product Grade B For Pipe Flange Connection [GB]
GB /T 9125 - 2010
Double End Studs - Product Grade B For Pipe Flange Connection

View Suppliers
22 Connections With Double End Studs - Type GR [DIN]
DIN 2510-4 (GR) - 1971
Connections With Double End Studs - Type GR
23 Connections With Double End Studs - Type HR [DIN]
DIN 2510-4 (HR) - 1971
Connections With Double End Studs - Type HR
24 Clamping type studs [ASME]
ASME B 18.31.2 - 2008
Clamping type studs
25 Connections With Waisted Stud - Type K [DIN]
DIN 2510-3 (K) - 1971
Connections With Waisted Stud - Type K
26 Studs - Metal End ≈ 2 d [DIN]
DIN 835 - 2010
Studs - Metal End ≈ 2 d
27 Connections With Double End Studs - Type GS [DIN]
DIN 2510-4 (GS) - 1971
Connections With Double End Studs - Type GS
28 Dimensions for Tap-End Studs (1.5d Engagement) (Inch Series)(A193 / A320 / A437 / A453 / A540 / A1014)[Table 3] [ASME]
ASME B 18.31.2 - 2014
Dimensions for Tap-End Studs (1.5d Engagement) (Inch Series)(A193 / A320 / A437 / A453 / A540 / A1014)[Table 3]
29 Studs For Use With T-Nuts ( Long b1 ) [DIN]
DIN 6379 - 2003
Studs For Use With T-Nuts ( Long b1 )
30 Connections With Double End Studs - Type GQ [DIN]
DIN 2510-4 (GQ) - 1971
Connections With Double End Studs - Type GQ
31 Connections With Double End Studs - Type HS [DIN]
DIN 2510-4 (HS) - 1971
Connections With Double End Studs - Type HS
32 Special Foundation Bolts [DIN]
DIN 797 - 2009
Special Foundation Bolts
33 Connections With Waisted Stud - Type L [DIN]
DIN 2510-3 (L) - 1971
Connections With Waisted Stud - Type L
34 Metric Double End Studs [IFI]
IFI 528 - 1999
Metric Double End Studs
35 double end studs (ASTM A354 / A449 / F593 / SAE J429) [ASME]
ASME B 18.31.2 - 2008
double end studs (ASTM A354 / A449 / F593 / SAE J429)
36 Connections With Waisted Stud - Type KU [DIN]
DIN 2510-3 (KU) - 1971
Connections With Waisted Stud - Type KU
37 Special Foundation Bolts [DIN]
DIN 797 - 1970
Special Foundation Bolts
38 Studs For Use With T-Nuts [DIN]
DIN 6379 - 2003
Studs For Use With T-Nuts
39 Metric Tap-End Studs (1.50 Engagement) [Table 3] (ASTM F568, F738M, F468M) [ASME]
ASME B 18.31.1M - 2008 (R2016)
Metric Tap-End Studs (1.50 Engagement) [Table 3] (ASTM F568, F738M, F468M)
40 Dimensions for Clamping Type Studs(A193 / A320 / A437 / A453 / A540 / A1014) (Inch Series) [Table 2] [ASME]
ASME B 18.31.2 - 2014
Dimensions for Clamping Type Studs(A193 / A320 / A437 / A453 / A540 / A1014) (Inch Series) [Table 2]
41 Stude Threaded End ≈2d [DIN]
DIN 835 - 1972
Stude Threaded End ≈2d
42 Connections With Waisted Stud - Type ZU [DIN]
DIN 2510-3 (ZU) - 1971
Connections With Waisted Stud - Type ZU
43 Double End Studs [DIN]
DIN 2509 - 2016
Double End Studs
44 Connections With Waisted Stud - Type Z [DIN]
DIN 2510-3 (Z) - 1971
Connections With Waisted Stud - Type Z
45 Double end studs [DIN]
DIN 2509 - 1986
Double end studs
46 Connections With Double End Studs - Type GP [DIN]
DIN 2510-4 (GP) - 1971
Connections With Double End Studs - Type GP
47 Stude Threaded End ≈2d [DIN]
DIN 835 - 1995
Stude Threaded End ≈2d
48 Connections With Double End Studs - Type HP [DIN]
DIN 2510-4 (HP) - 1971
Connections With Double End Studs - Type HP
49 Metric Clamping-Type Studs [Table 2] (ASTM F568, F738M, F468M) [ASME]
ASME B 18.31.1M - 2008 (R2016)
Metric Clamping-Type Studs [Table 2] (ASTM F568, F738M, F468M)
50 Connections With Double End Studs - Type HQ [DIN]
DIN 2510-4 (HQ) - 1971
Connections With Double End Studs - Type HQ
51 Connections With Waisted Stud - Type SD [GB]
GB /T 13807.2 (SD) - 2008
Connections With Waisted Stud - Type SD
52 Stainless Steel Double-end Stud Bolt [JIS]
JIS A 5540 - 2008
Stainless Steel Double-end Stud Bolt
53 Long Metal End Studs - ISO Metric Coarse Thread [UNI]
UNI 5914
Long Metal End Studs - ISO Metric Coarse Thread
54 Screwd Studs - B.S.F. Thread  [Table 5] [BS]
BS 2693-1 - 1956
Screwd Studs - B.S.F. Thread [Table 5]
55 Set of Anchor Bolt with Rolled Threads for Structures - ABR [JIS]
JIS B 1220 (ABR) - 2015
Set of Anchor Bolt with Rolled Threads for Structures - ABR
56 Medium End Studs (b1=1.5d)-ISO Metric Coarse Thread - Product Grade A [UNI]
UNI 5911 - 1993
Medium End Studs (b1=1.5d)-ISO Metric Coarse Thread - Product Grade A
57 Double End Studs, bm=1d [UNI]
UNI 5909 - 1966
Double End Studs, bm=1d
58 Connections With Waisted Stud - Type L [GB]
GB /T 13807.2 (L) - 2008
Connections With Waisted Stud - Type L
59 Double-end Dtud Bolt, Carbon steel and hot-clip zinc coated carbon steel [JIS]
JIS A 5540 - 2008
Double-end Dtud Bolt, Carbon steel and hot-clip zinc coated carbon steel
60 Screwd Studs - B.A. Thread  [Table 7] [BS]
BS 2693-1 - 1956
Screwd Studs - B.A. Thread [Table 7]
61 Set of Anchor Bolt with cut Threads for Structures - ABM [JIS]
JIS B 1220 (ABM) - 2015
Set of Anchor Bolt with cut Threads for Structures - ABM
62 Set of Anchor Bolt with Rolled Threads for Structures [JIS]
JIS B 1220 - 2010
Set of Anchor Bolt with Rolled Threads for Structures
63 Screwd Studs - UNF Thread  [Table 3] [BS]
BS 2693-1 - 1956
Screwd Studs - UNF Thread [Table 3]
64 Bolts of Turnbuckle for Building Made of Rolling Steel - Double Ended Stud [JIS]
JIS A 5542 (A3) - 2003
Bolts of Turnbuckle for Building Made of Rolling Steel - Double Ended Stud
65 Studs - Product A And B b1=1.5d [NF]
NF E 25-135 - 1986
Studs - Product A And B b1=1.5d
66 Medium End Studs  -ISO Metric Coarse Thread - Product Grade A [UNI]
UNI 5911 - 1966
Medium End Studs -ISO Metric Coarse Thread - Product Grade A
67 Screwd Studs - UNC Thread [Table 4] [BS]
BS 2693-1 - 1956
Screwd Studs - UNC Thread [Table 4]
68 Double End Studs, bm=1d [UNI]
UNI 5909 - 1993
Double End Studs, bm=1d
69 Connections With Waisted Stud - Type S [GB]
GB /T 13807.2 (S) - 2008
Connections With Waisted Stud - Type S
70 Connections With Waisted Stud-Studs - Type S [GB]
GB /T 13807.2 - 1992
Connections With Waisted Stud-Studs - Type S
71 Studs - Product A And B  (b1=1d, 1.25d 或 2d) [NF]
NF E 25-135 - 1986
Studs - Product A And B (b1=1d, 1.25d 或 2d)
72 Connections With Waisted Stud - Type AD [GB]
GB /T 13807.2 (AD) - 2008
Connections With Waisted Stud - Type AD
73 Connections With Waisted Stud - Type A [GB]
GB /T 13807.2 (A) - 2008
Connections With Waisted Stud - Type A
74 Double End Studs [GOST]
GOST 22032 - 1976
Double End Studs
75 Flange Connections of Wellhead Equipment - Stud - Modification 2 [GOST]
GOST 28919 - 1991
Flange Connections of Wellhead Equipment - Stud - Modification 2
76 Flange Connections of Wellhead Equipment  - Stud - Modification 1 [GOST]
GOST 28919 - 1991
Flange Connections of Wellhead Equipment - Stud - Modification 1
77 Double End Studs [CNS]
CNS 4606 - 1983
Double End Studs
78 Double End Studs For T-Nuts [CNS]
CNS 4607 - 1983
Double End Studs For T-Nuts
79 Double End Studs [CNS]
CNS 4609 - 1983
Double End Studs
80 Double End Studs [CNS]
CNS 4603 - 1978
Double End Studs
81 Double End Studs [CNS]
CNS 4604 - 1978
Double End Studs
82 Double End Studs [CNS]
CNS 4605 - 1978
Double End Studs
83 Double End Studs [YJT]
YJT 2003 (BCEQ-9411 A1)
Double End Studs