| 简体 | 繁體 |

Screwd Studs - B.S.F. Thread [Table 5]

BS 2693-1 - 1956

Display drawing:

英标BS 2693-1 - 1956 BS2693-1 2693-1BS Screwd Studs - B.S.F. Thread  [Table 5]
Screw Thread
d
1/4 5/16 3/8 7/16 1/2 9/16 5/8 3/4 7/8 1 1-1/8 1-1/4 1-3/8 1-1/2
PP
Major diameter max
min
Effective diameter max
min
Minor diameter max
min
L min b1=d
b1=1.5d
D
26 22 20 18 16 16 14 12 11 10 9 9 8 8
0.2500 0.3125 0.3750 0.4375 0.5000 0.5625 0.6250 0.7500 0.8750 1.0000 1.1250 1.2500 1.3750 1.5000
0.2455 0.3077 0.3699 0.4320 0.4942 0.5566 0.6187 0.7432 0.8678 0.9924 1.1171 1.2419 1.3665 1.4913
0.2280 0.2863 0.3461 0.4053 0.4637 0.5263 0.5833 0.7009 0.8214 0.9411 1.0592 1.1844 1.3006 1.4258
0.2251 0.2832 0.3429 0.4019 0.4600 0.5225 0.5793 0.6966 0.8168 0.9360 1.0539 1.1789 1.2950 1.4200
0.2034 0.2572 0.3141 0.3697 0.4237 0.4863 0.5376 0.6475 0.7632 0.8771 0.9881 1.1133 1.2206 1.3458
0.1984 0.2517 0.3083 0.3635 0.4172 0.4797 0.5305 0.6398 0.7551 0.8686 0.9792 1.1042 1.2110 1.3360
7/8 1-1/8 1-3/8 1-5/8 1-3/4 2 2-1/4 2-5/8 3-1/8 3-1/2 4 4-1/2 4-3/4 5-1/4
1 1-1/4 1-1/2 1-3/4 2 2-1/4 2-1/2 3 3-1/2 4 4-1/2 5 5-1/2 6
1/4 5/16 3/8 7/16 1/2 9/16 5/8 3/4 7/8 1 1-1/8 1-1/4 1-3/8 1-1/2
①,The length of thread on the nut end of the stud shall not include the run-out threads and shall be equal to twice the nominal diameter of the thread, except in the case of short studs where this would result in a length of plain portion less than 1/ 2 D. In such cases a length of plain portion equal to 1/ 2 D should be allowed for before threading the remainder for the nut end.
②,Metal end (b1):
i) The length of the thread on the metal end of the stud shall include the run-out threads and shall be equal to the nominal diameter of the thread or to one and a half times the nominal diameter of the
thread, as specified by the purchaser.
ii) The length of thread run-out shall be not less than 2 pitches or more than 2-1/2 pitches.
iii) The tolerance on the length of the thread shall be plus or minus 1/32 in., or plus or minus half a pitch, whichever is the greater.
③,Ends of studs:
a) Metal end: The metal end of the stud shall be finished with a flat chamfer with a 90° included angle to a depth slightly exceeding the depth of thread.
b) Nut end: The nut end of the stud (except studs with Unified threads) shall be finished with a radius approximately equal to 11/ 4 times the nominal diameter. Unified threads shall have a shallow dog point machined on the nut end.

Similar Standards

1 Studs - Metal end ≈ 1,25 d [DIN]
DIN 939 - 1995
Studs - Metal end ≈ 1,25 d

View Suppliers
2 Double Studs [JIS]
JIS B 1173 - 1995
Double Studs

View Suppliers
3 Studs [JIS]
JIS B 1173 - 2010
Studs

View Suppliers
4 Double End Studs-bm=1.25d [GB]
GB 898 - 1988
Double End Studs-bm=1.25d

View Suppliers
5 Double End Studs (Clamping Type) - Product Grade B [GB]
GB 901 - 1988
Double End Studs (Clamping Type) - Product Grade B

View Suppliers
6 Double End Studs-bm=2d [GB]
GB 900 - 1988
Double End Studs-bm=2d

View Suppliers
7 Connections with Waisted Stud - Type Z [DIN]
DIN 2510-3 (Z) - 1971
Connections with Waisted Stud - Type Z
8 Special Foundation Bolts [DIN]
DIN 797 - 2009
Special Foundation Bolts
9 Connections with Double End Studs - Type HP [DIN]
DIN 2510-4 (HP) - 1971
Connections with Double End Studs - Type HP
10 Connections with Double End Studs - Type GS [DIN]
DIN 2510-4 (GS) - 1971
Connections with Double End Studs - Type GS
11 Studs with Metric Interference Thread MFS - Part 2: Lengths of Engagement ≈ 2.5 d (Type B) [DIN]
DIN 949 (-2) - 1995
Studs with Metric Interference Thread MFS - Part 2: Lengths of Engagement ≈ 2.5 d (Type B)
12 Double End Studs (ASTM A354 / A449 / F593 / SAE J429) [ASME]
ASME B 18.31.2 - 2008
Double End Studs (ASTM A354 / A449 / F593 / SAE J429)
13 Studs with A Length of Engagement Equal to About 1d [DIN]
DIN 938 - 1995
Studs with A Length of Engagement Equal to About 1d
14 Connections with Double End Studs - Type GR [DIN]
DIN 2510-4 (GR) - 1971
Connections with Double End Studs - Type GR
15 Connections with Double End Studs - Type GP [DIN]
DIN 2510-4 (GP) - 1971
Connections with Double End Studs - Type GP
16 Metric Clamping-Type Studs [Table 2] (ASTM F568, F738M, F468M) [ASME]
ASME B 18.31.1M - 2008 (R2016)
Metric Clamping-Type Studs [Table 2] (ASTM F568, F738M, F468M)
17 Connections with Waisted Stud - Type KU [DIN]
DIN 2510-3 (KU) - 1971
Connections with Waisted Stud - Type KU
18 Studs with a Length of Engagement Equal to About 2.5d [DIN]
DIN 940 - 2010
Studs with a Length of Engagement Equal to About 2.5d
19 Dimensions for Tap-End Studs (1.5d Engagement) (Inch Series)(A193 / A320 / A437 / A453 / A540 / A1014)[Table 3] [ASME]
ASME B 18.31.2 - 2014
Dimensions for Tap-End Studs (1.5d Engagement) (Inch Series)(A193 / A320 / A437 / A453 / A540 / A1014)[Table 3]
20 Double End Studs [DIN]
DIN 2509 - 2016
Double End Studs
21 Connections with Waisted Stud - Type K [DIN]
DIN 2510-3 (K) - 1971
Connections with Waisted Stud - Type K
22 Metric Double End Studs [IFI]
IFI 528 - 1999
Metric Double End Studs
23 Clamping Type Studs [ASME]
ASME B 18.31.2 - 2008
Clamping Type Studs
24 Connections with Waisted Stud - Type ZU [DIN]
DIN 2510-3 (ZU) - 1971
Connections with Waisted Stud - Type ZU
25 Dimensions for Clamping Type Studs(A193 / A320 / A437 / A453 / A540 / A1014) (Inch Series) [Table 2] [ASME]
ASME B 18.31.2 - 2014
Dimensions for Clamping Type Studs(A193 / A320 / A437 / A453 / A540 / A1014) (Inch Series) [Table 2]
26 Connections with Double End Studs - Type HR [DIN]
DIN 2510-4 (HR) - 1971
Connections with Double End Studs - Type HR
27 Connections with Double End Studs - Type GQ [DIN]
DIN 2510-4 (GQ) - 1971
Connections with Double End Studs - Type GQ
28 Studs for Use with T-Nuts ( Long b1 ) [DIN]
DIN 6379 - 2003
Studs for Use with T-Nuts ( Long b1 )
29 Double End Studs [IFI]
IFI 136 - 2006
Double End Studs
30 Double End Studs [DIN]
DIN 2509 - 1986
Double End Studs
31 Studs for Use with T-Nuts [DIN]
DIN 6379 - 2003
Studs for Use with T-Nuts
32 Stude Threaded End ≈2d [DIN]
DIN 835 - 1972
Stude Threaded End ≈2d
33 Studs with Metric Interference Thread MFS - Part 1: Lengths of Engagement ≈ 2 d (Type A) [DIN]
DIN 949-1 - 1995
Studs with Metric Interference Thread MFS - Part 1: Lengths of Engagement ≈ 2 d (Type A)
34 Studs with a Length of Engagement Equal to About 2.5d [DIN]
DIN 940 - 1983
Studs with a Length of Engagement Equal to About 2.5d
35 Studs - Metal End ≈ 2 d [DIN]
DIN 835 - 2010
Studs - Metal End ≈ 2 d
36 Special Foundation Bolts [DIN]
DIN 797 - 1970
Special Foundation Bolts
37 Connections with Double End Studs - Type HS [DIN]
DIN 2510-4 (HS) - 1971
Connections with Double End Studs - Type HS
38 Metric Tap-End Studs (1.50 Engagement) [Table 3] (ASTM F568, F738M, F468M) [ASME]
ASME B 18.31.1M - 2008 (R2016)
Metric Tap-End Studs (1.50 Engagement) [Table 3] (ASTM F568, F738M, F468M)
39 Connections with Waisted Stud - Type L [DIN]
DIN 2510-3 (L) - 1971
Connections with Waisted Stud - Type L
40 Stude Threaded End ≈2d [DIN]
DIN 835 - 1995
Stude Threaded End ≈2d
41 Connections with Double End Studs - Type HQ [DIN]
DIN 2510-4 (HQ) - 1971
Connections with Double End Studs - Type HQ
42 Studs - Metal End ≈ 2.5d [DIN]
DIN 940 - 1995
Studs - Metal End ≈ 2.5d
43 Studs - Metal End ≈ 1 d [DIN]
DIN 938 - 2012
Studs - Metal End ≈ 1 d
44 Screwd Studs - B.A. Thread  [Table 7] [BS]
BS 2693-1 - 1956
Screwd Studs - B.A. Thread [Table 7]
45 Double End Studs(Clamping Type) - Product Grade C [GB]
GB 953 - 1988
Double End Studs(Clamping Type) - Product Grade C
46 Stainless Steel Double-end Stud Bolt [JIS]
JIS A 5540 - 2008
Stainless Steel Double-end Stud Bolt
47 Double End Studs for Pipe Flange Connection - PN Designated [GB]
GB /T 9125.1 - 2020
Double End Studs for Pipe Flange Connection - PN Designated
48 Medium End Studs  -ISO Metric Coarse Thread - Product Grade A [UNI]
UNI 5911 - 1966
Medium End Studs -ISO Metric Coarse Thread - Product Grade A
49 Connections with Waisted Stud - Type A [GB]
GB /T 13807.2 (A) - 2008
Connections with Waisted Stud - Type A
50 Medium End Studs (b1=1.5d)-ISO Metric Coarse Thread - Product Grade A [UNI]
UNI 5911 - 1993
Medium End Studs (b1=1.5d)-ISO Metric Coarse Thread - Product Grade A
51 Connections with Waisted Stud - Type S [GB]
GB /T 13807.2 (S) - 2008
Connections with Waisted Stud - Type S
52 Studs - Product A and B  (b1=1d, 1.25d 或 2d) [NF]
NF E 25-135 - 1986
Studs - Product A and B (b1=1d, 1.25d 或 2d)
53 Double-end Dtud Bolt, Carbon Steel and Hot-clip Zinc Coated Carbon Steel [JIS]
JIS A 5540 - 2008
Double-end Dtud Bolt, Carbon Steel and Hot-clip Zinc Coated Carbon Steel
54 Double End Studs, bm=1d [UNI]
UNI 5909 - 1993
Double End Studs, bm=1d
55 Double End Studs - Product Grade B for Pipe Flange Connection [GB]
GB /T 9125 - 2010
Double End Studs - Product Grade B for Pipe Flange Connection
56 Screwd Studs - UNF Thread  [Table 3] [BS]
BS 2693-1 - 1956
Screwd Studs - UNF Thread [Table 3]
57 Connections With Waisted Stud-Studs - Type S [GB]
GB /T 13807.2 - 1992
Connections With Waisted Stud-Studs - Type S
58 Double End Studs for Pipe Flange Connection [GB]
GB /T 9125 - 2003
Double End Studs for Pipe Flange Connection
59 Long Metal End Studs - ISO Metric Coarse Thread - Finiah A [UNI]
UNI 59141966
Long Metal End Studs - ISO Metric Coarse Thread - Finiah A
60 Double End Studs, bm=1d [UNI]
UNI 5909 - 1966
Double End Studs, bm=1d
61 Screwd Studs -B.S.W.Thread  [Table 6] [BS]
BS 2693-1 - 1956
Screwd Studs -B.S.W.Thread [Table 6]
62 Double End Studs  b1=1.5d [GB]
GB 899 - 1988
Double End Studs b1=1.5d
63 Set of Anchor Bolt with Cut Threads for Structures - ABM [JIS]
JIS B 1220 (ABM) - 2015
Set of Anchor Bolt with Cut Threads for Structures - ABM
64 Studs - Product A and B b1=1.5d [NF]
NF E 25-135 - 1986
Studs - Product A and B b1=1.5d
65 Double End Studs for Pipe Flange Connection [GB]
GB /T 9125 - 2010
Double End Studs for Pipe Flange Connection
66 Connections with Waisted Stud - Type SD [GB]
GB /T 13807.2 (SD) - 2008
Connections with Waisted Stud - Type SD
67 Screwd Studs - UNC Thread [Table 4] [BS]
BS 2693-1 - 1956
Screwd Studs - UNC Thread [Table 4]
68 Connections with Waisted Stud - Type L [GB]
GB /T 13807.2 (L) - 2008
Connections with Waisted Stud - Type L
69 Set of Anchor Bolt with Rolled Threads for Structures [JIS]
JIS B 1220 - 2010
Set of Anchor Bolt with Rolled Threads for Structures
70 Double End Studs, bm=1d [GB]
GB 897 - 1988
Double End Studs, bm=1d
71 Connections with Waisted Stud - Type AD [GB]
GB /T 13807.2 (AD) - 2008
Connections with Waisted Stud - Type AD
72 Bolts of Turnbuckle for Building Made of Rolling Steel - Double Ended Stud [JIS]
JIS A 5542 (A3) - 2003
Bolts of Turnbuckle for Building Made of Rolling Steel - Double Ended Stud
73 Set of Anchor Bolt with Rolled Threads for Structures - ABR [JIS]
JIS B 1220 (ABR) - 2015
Set of Anchor Bolt with Rolled Threads for Structures - ABR
74 Double End Studs - Type 2 [OCT]
OCT 26 - 2040 (Type 2) - 1996
Double End Studs - Type 2
75 Double End Studs - Type 1 [OCT]
OCT 26 - 2040 (Type 1) - 1996
Double End Studs - Type 1
76 Double End Studs [GOST]
GOST 22032 - 1976
Double End Studs
77 Flange Connections of Wellhead Equipment - Stud - Modification 2 [GOST]
GOST 28919 - 1991
Flange Connections of Wellhead Equipment - Stud - Modification 2
78 Double End Studs [CNS]
CNS 4606 - 1983
Double End Studs
79 Double End Studs for T-Nuts [CNS]
CNS 4607 - 1983
Double End Studs for T-Nuts
80 Double End Studs [CNS]
CNS 4609 - 1983
Double End Studs
81 Double End Studs [CNS]
CNS 4603 - 1978
Double End Studs
82 Double End Studs [CNS]
CNS 4604 - 1978
Double End Studs
83 Double End Studs [CNS]
CNS 4605 - 1978
Double End Studs
84 Flange Connections of Wellhead Equipment  - Stud - Modification 1 [GOST]
GOST 28919 - 1991
Flange Connections of Wellhead Equipment - Stud - Modification 1
85 Double End Studs [YJT]
YJT 2003 (BCEQ-9411 A1)
Double End Studs